Nationwide Shipping
★ SSPC AWARD-WINNING SYSTEM TOPCOAT · 5,000-HOUR SALT SPRAY TESTED · THREE FORMULAS

Enamo Grip

The Topcoat That Sealed the Hoover Dam Bypass — Two-Part Polyurethane Armor in Three Formulas

Enamo Grip® is a two-part aliphatic polyurethane enamel that self-levels into a uniquely hard, smooth film with unsurpassed gloss and color retention — the topcoat that finished the SSPC award-winning Rust Grip® system on the Hoover Dam Bypass Bridge. It shrugs off water, humidity, stains, chemicals, scuffs, and impact, and it comes in three formulas: the proven original (ABS-approved (original formula), 5,000-hour salt-spray tested), Enamo Grip II (ultra-low-VOC water-based at just 22 g/L, soap-and-water cleanup), and Enamo Grip 5000 (polyester-hybrid chemistry for acid, alkali, and fuel exposure across pH 5–14). Clear and colors. Made in USA.

Enamo Grip Two-Part Kit — Base + Curing Agent
Enamo Grip Two-Part Kit — Base + Curing Agent
Hoover Dam Bypass Bridge — Structural Steel Topcoat
Enamo Grip - Hoover Dam Bypass Bridge — Structural Steel Topcoat
Self-Leveled Semi-Gloss Finish, Close-Up
Enamo Grip - Self-Leveled Semi-Gloss Finish, Close-Up
Industrial Floor — Machine Traffic Zone
Enamo Grip - Industrial Floor — Machine Traffic Zone
Enamo Grip II Water-Based — Interior Application
Enamo Grip II Water-Based — Interior Application
EG5000 on Chemical Containment Curb
Enamo Grip - EG5000 on Chemical Containment Curb
Clear Coat Over Rust Grip on Restored Equipment
Enamo Grip - Clear Coat Over Rust Grip on Restored Equipment

Enamo Grip · Enamo Grip II · Enamo Grip 5000 — Pre-Measured Two-Part Kits · Clear & Colors · Ships Nationwide

What Does Your Project Need?

Enamo Grip® (Original) selected — specs, calculator, and order form below are set to the original formula.

AS
About Arin Shahmoradian
Official USA distributor of Rust Grip® (SPI Coatings). Volta Coatings has shipped Rust Grip to industrial, marine, farm, and residential customers across the United States and internationally for over a decade. Direct technical support before, during, and after every project. Reach him directly at +18186963786 or arin@voltacoatings.com

What Makes a Two-Part Polyurethane Different?

One-part paints dry; Enamo Grip cures by chemical reaction. Mixing the base with its curing agent starts a cross-linking reaction that builds a film far harder and more chemical-resistant than anything evaporation alone can produce — self-leveling to a smooth, even finish with impact resistance of 160 psi front / 100 psi back (original formula) and gloss that holds without chalking in full sun. It's the finish coat of the SPI system: Rust Grip® encapsulates the steel, Enamo Grip locks in the color, gloss, and chemical barrier on top.

Where Does Enamo Grip Get Used?

One documented flagship — and the manufacturer's specified uses across the family.

Enamo Grip - Hoover Dam Bypass Bridge

Hoover Dam Bypass Bridge

📍 Nevada/Arizona, USA

Topcoat of the Rust Grip® + Enamo Grip® system on the bridge's structural steel — SSPC E. Crone Knoy Award winner, in service since the bridge opened in 2010 — more than 15 years.

✓ VERIFIED
Enamo Grip - Topcoat for Rust Grip® & Moist Metal Grip

Topcoat for Rust Grip® & Moist Metal Grip

The specified finish coat over SPI's encapsulating primers — color, gloss, UV stability, and a chemical barrier over the corrosion protection.

Rust Grip →

Enamo Grip - Industrial & Commercial Floors

Industrial & Commercial Floors

A tough, long-lasting floor covering for machine and foot traffic — second coat specified in wear zones, handrails, and walkways.

Enamo Grip - Marine & Offshore (Original)

Marine & Offshore (Original)

ABS-approved for saltwater/maritime use — USCG and IMO approvals under renewal per the current TDS — plus 5,000-hour salt-spray endurance.

Enamo Grip - Chemical Exposure Zones (EG5000)

Chemical Exposure Zones (EG5000)

Containment curbs, wash-down areas, battery rooms, fuel-handling zones — service across pH 5–14 with gasoline, diesel, and Skydrol resistance.

Enamo Grip - Occupied & VOC-Regulated Facilities (EG II)

Occupied & VOC-Regulated Facilities (EG II)

Schools, hospitals, food plants, and California job sites: 22 g/L VOC, water-based, soap-and-water cleanup — applied where solvent coatings are restricted.

Laboratory and field project results may vary according to climate conditions.

How Tough Is Enamo Grip? Technical Performance Data

Salt Spray Endurance

5,000 Hours

Original Formula

ASTM B117 salt spray and ASTM D5894 UV/salt-spray cyclic testing — the corrosion-chamber marathon most topcoats never attempt.

Impact Resistance

160 / 100 psi

Original Formula

Front and back impact with tremendous scuff and mar resistance — a film that takes abuse and keeps its finish.

Fire Rating

Class A

ASTM E84 flame-spread Class A rating.

Gloss & UV Stability

No Chalking

Original Formula

Aliphatic chemistry with unsurpassed semi-gloss and color retention — verified through 5,000 hours of UV/salt-spray cycling.

Chemical Service (EG5000)

pH 5 – 14

The 5000 formula: outstanding alkali, very good acid, plus gasoline, diesel, and Skydrol resistance. 3H pencil hardness.

Ultra-Low VOC (EG II)

22 g/L

Enamo Grip II delivers the two-part polyurethane film at 22 grams per liter — water-based, soap-and-water cleanup, non-hazmat shipping.

Which Enamo Grip Do You Need?

All three formulas cure to the same idea: a self-leveling, two-part polyurethane film that's uniquely hard, smooth, and UV-stable. The difference is what your project demands. Choose the original for maximum proven durability, Enamo Grip II for VOC compliance and easy cleanup, and Enamo Grip 5000 for chemical exposure.

Enamo Grip® — The Original

Solvent-based aliphatic PU · Mix 3:1 · 244 g/L (white)

The full test battery lives here: USDA acceptance, ABS marine approval (USCG and IMO under renewal per TDS), ASTM E84 Class A, D4060 abrasion, D6904 wind-driven rain, E96 vapor transmission, and 5,000-hour B117/D5894 chamber endurance. Clear in high-gloss, semi-gloss, and matt, plus colors. When the specification says proven, this is the sheet you attach.

Enamo Grip® II — The Compliance Answer

Water-based PU · Mix 2:1 · 22 g/L · Soap-and-water cleanup

The same hard, self-leveling two-part film at roughly 1/11th the VOC of the original — inside occupied buildings, in strict air districts, and anywhere solvent odor is a dealbreaker. Water-based classification also means standard, non-hazmat shipping.

Enamo Grip® 5000 — The Chemistry Set

Polyester/PU hybrid · Mix 2:1 · pH 5–14 · 3H hardness

A saturated polyester on a urethane backbone: high cross-link density for chemical resistance with internal flexibility. Outstanding alkali, very good acid, and documented resistance to gasoline, diesel, animal fats, and Skydrol. Field rules that keep it performing: rinse acid splash within 72 hours, never build thick coats, no total submersion.

Scope: HOn corroded or non-porous steel, all three are topcoats over Rust Grip® primer per specification.

Enamo Grip in the Field

Click thumbnails to view full size.

Enamo Grip - Project Image 1Enamo Grip - Project Image 2Enamo Grip - Project Image 3Enamo Grip - Project Image 4Enamo Grip - Project Image 5Enamo Grip - Project Image 6Enamo Grip - Project Image 7Enamo Grip - Project Image 8Enamo Grip - Project Image 9Enamo Grip - Project Image 10Enamo Grip - Project Image 11Enamo Grip - Project Image 12

Application: The Rules That Make or Break an Enamo Grip Job

Field guidance from Arin Shahmoradian, USA Distributor — based on SPI application instructions

RULE #1 — MOST IMPORTANT
Respect the clock: pot life and the overcoat window run the job.
Once base meets curing agent, you have 4–6 hours of pot life at 70°F — just 1 hour at 90°F (set pails in ice water to stretch it). Recoat windows differ by formula: Enamo Grip Original, 3 hours or less at 70°F; Enamo Grip II, up to 24 hours while the first coat is tacky with little to no transfer; Enamo Grip 5000, 3–4 hours. After the applicable overcoat window, lightly sand before the next coat. Plan the day around the chemistry, not the other way around.
Mix exactly — never thin with mineral spirits.
Original: 3 parts base to 1 part curing agent by volume. EG II and EG5000: 2 to 1. Mix two minutes by hand or 30+ seconds by drill with NO vortex. Never use mineral spirits to prep or thin; never apply on or within 2 inches of chlorinated rubber. Hot and humid (90°F/85% RH)? Cut the original or 5000 kit with one quart of MAK solvent — EG II takes one quart of distilled water instead.
Prime with Rust Grip®, sand the gloss, stay above the dew point.
On non-porous or corroded steel, Rust Grip® is the specified primer. Any existing glossy finish must be sanded dull first. Apply between 40–100°F, always at least 5° above the dew point, on completely dry, salt-decontaminated surfaces.
SURFACES
Metal, concrete, masonry, wood, and other porous surfaces. Rust Grip® primer on non-porous/corroded steel.
FILM BUILD
Original & 5000: ~200 ft²/gal per coat (8 mils wet). EG II: ~275 ft²/gal (6 mils wet). Clear: up to ~400 ft²/gal. 2nd coat in wear zones.
APPLICATION
Soft-bristle brush, 1/4" nap roller, or airless (1.5 gpm @ 3,300 psi, .011–.015 tip). Roll/brush: +2 oz Bubble Breaker (orig.) or potable water (EG II) per gallon.
CURE
Tack-free 30–60 min at 70°F. Full cure 10 days (orig./II); 5000 in service at 15 days (80% in 72 hrs). Max 300°F cured.
CLEANUP AND SAFETY
Original & 5000: MEK/solvent, hazmat freight (Class 3, UN1263). EG II: soap and water, standard freight.

EG5000 service limits: not for total submersion; rinse acid splash within 72 hours; never apply thick coats — let thin coats tack before the next.

Why Enamo Grip Outperforms Ordinary Enamels

Cures, Doesn't Just Dry
Chemical-reaction cure builds cross-linked hardness no air-dry enamel can match — with self-leveling that erases brush and roller marks into a smooth, even film.
Holds Its Gloss in the Sun
Aliphatic chemistry means unsurpassed semi-gloss and color retention with chalk resistance — proven through 5,000 hours of UV/salt-spray cycling.
Takes the Hit
160 psi front-impact resistance plus tremendous scuff and mar resistance — floors, handrails, and equipment that keep their finish under traffic.
Three Formulas, One Spec Sheet
Solvent-proven, water-based compliant, or chemical-hybrid — the right chemistry for the job without leaving the SPI system.
The System Finish
Purpose-built as the topcoat for Rust Grip® and Moist Metal Grip — the same pairing that earned the SSPC award on the Hoover Dam Bypass.
Clear or Color, Any Sheen
Clear in high-gloss, semi-gloss, and matt (original), plus colors across the family with established minimum order quantities.

What Certifications and Testing Does Enamo Grip Hold?

USDA
Accepted for use in regulated facilities.
ABS · USCG · IMO
ABS marine approval for saltwater/maritime use; USCG and IMO under renewal per current TDS.
ASTM E84
Class A flame-spread fire rating.
ASTM B117 / D5894
5,000-hour salt spray and 5,000-hour UV/salt-spray cyclic endurance.
D4060 / D6904 / E96
Abrasion, wind-driven rain, and water-vapor transmission tested.
★ Industry Recognition

SSPC Award: Hoover Dam Bypass Bridge

The Rust Grip® + Enamo Grip® system on the bridge's structural steel received the SSPC E. Crone Knoy Award for Innovation — and this page's product was the topcoat. After nearly 14 years in desert sun, the finish remains in service. Photo set includes the award ceremony and the re-inspection series.

The complete system: Rust Grip® encapsulation + Enamo Grip® finish, with Super Therm® on the pedestrian handrails.

Enamo Grip - Hoover Dam Bypass Bridge

Purchase Enamo Grip. Nationwide Shipping.

All three formulas ship anywhere in the United States — EG II as standard freight; original and 5000 as hazmat ground. Talk to Arin Shahmoradian directly for formula selection, color and sheen, kit counts, and system specs with Rust Grip®. Monday–Saturday. Authorized SPI Distributor — Volta Coatings.

  • By submitting, you agree to our Terms of Service and Privacy Policy

    Both checkboxes optional — the form submits either way.

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.

The Enamo Grip Family, Compared

Attribute Enamo Grip (Original) Enamo Grip II Enamo Grip 5000
Chemistry Solvent-based aliphatic polyurethane Water-based polyurethane Aliphatic polyester/polyurethane hybrid
Reactive VOC 244 g/L white · 304 g/L clear 22 g/L ★ 169 g/L
Mix ratio (by volume) 3 : 1 2 : 1 2 : 1
Reacted solids (white) 64% wt / 49% vol 64% wt / 61% vol 76% wt / 60% vol
Signature strength Full test battery, marine approvals, 160/100 psi impact Compliance + cleanup: soap & water, non-hazmat Chemical service pH 5–14, fuels & Skydrol, 3H hardness
Spread rate (pigmented) ~200 ft²/gal per coat ~275 ft²/gal per coat ~200 ft²/gal per coat
Pot life @ 70°F / 90°F 4–6 hrs / 1 hr 4–6 hrs / 1 hr 3–4 hrs / 1 hr
Full cure 10 days 10 days 15 days for service (80% in 72 hrs)
Cleanup MEK / solvent Soap and water ★ MEK / solvent
Shipping Hazmat (Class 3, UN1263) Non-hazmat standard freight ★ Hazmat (Class 3, UN1263)
Certifications USDA, ABS (USCG/IMO renewing), E84 Class A, 5,000-hr B117/D5894
"Same family, same self-leveling armor — pick the original for the résumé, the II for the air district, and the 5000 for the chemistry set."

What Are the Technical Specifications for Enamo Grip?

Chemistry / mix ratio Two-part aliphatic polyurethane · 3 : 1 by volume
Reacted solids White 64% wt / 49% vol · Clear HG 44/38 · SG 45/39.5 · Matt 47/41
Reactive VOC White 244 g/L (2.04 lbs/gal) · Clear 304 g/L (2.5 lbs/gal)
Viscosity / reacted weight 300–470 cP · White 11.02, Clear 8.31 lbs/gal
Impact resistance 160 psi front / 100 psi back
Average perms 0.6809
Tack-free / overcoat window 30–60 min at 70°F / 3 hours or less at 70°F
Pot life 4–6 hrs @ 70°F · 1 hr @ 90°F · ~1.5 hrs above 95°F (ice pails to extend)
Surface temp (applying / cured max) 40°F min – 150°F max / 300°F continuous
Full cure / shelf life 10 days / 3 years unopened
Clear finishes & spread High-gloss 406 ft²/gal · Semi-gloss 395 · Matt 386 (3.9–4.1 mils wet)
Chemistry / mix ratio Two-part ultra-low-VOC water-based polyurethane · 2 : 1 by volume or weight
Reacted solids White 64% wt / 61% vol · Clear HG 61/60
Reactive VOC 22 g/L (0.18 lbs/gal), white or clear
Viscosity / reacted weight 300–470 cP · White 9.67, Clear 8.97 lbs/gal
Tack-free / overcoat window 1–2 hrs at 70°F per TDS / 4 hours or less at 70°F
Pot life 4–6 hrs @ 70°F · 1 hr @ 90°F · can drop to 30–90 min above 95°F
Surface temp (applying / cured max) 40°F min – 150°F max / 300°F continuous
Shelf life 2 years unopened
Hot-climate adjustment Cut 3-gallon kit with one quart distilled/potable water (never MAK)
Cleanup / shipping Soap and water · non-hazmat standard freight
Tests & certifications Pending test results (per TDS 8/6/25)
Chemistry / mix ratio Two-part aliphatic polyester/polyurethane hybrid · 2 : 1 by volume (not weight)
Reacted solids White 76% wt / 60% vol · Clear 68/60
Reactive VOC 169 g/L (1.41 lbs/gal), white or clear
Hardness / impact 3H pencil hardness · 70 psi front / 5 psi back
Chemical service pH 5–14 · outstanding alkali, very good acid · gasoline, diesel, Skydrol, animal fats · non-sparking
Reacted weight White 11.6 lbs/gal · Clear 8.62 lbs/gal
Tack-free / overcoat window 30–60 min at 70°F / 3–4 hours or less at 70°F
Pot life 3–4 hrs @ 70°F · 1 hr @ 90°F
Cure 80% in 72 hrs; in service at 15 days @ 70°F. Recoat within 72 hrs, no prep; after 72 hrs, sand.
Surface temp (applying / cured max) 40°F min – 150°F max / 300°F continuous
Service limits Not for total submersion · rinse acid splash within 72 hours · never apply thick coats

Surface prep: clean of oil, tar, rust, grease, salts, and films — TSP or citrus cleaner plus 3,500 psi pressure wash; decontaminate salts to nitrates 5–10, sulfates 5–10, chlorides 3–5 mcg/cm²; surface completely dry; sand any glossy existing finish dull. Apply 40–100°F, minimum 5° above the dew point. Brush (soft bristle), 1/4-inch nap roller, or airless sprayer at 1.5 gal/min, 3,300 psi, .011–.015 tip. Never use mineral spirits to prep or thin; never apply on or within 2 inches of chlorinated rubber; over caulk, use only high-performance solvent-borne polyurethane caulk (EG II: high-performance paintable caulk). Recoat while tacky with little-to-no transfer; past that stage, lightly sand before the next coat.

Technical Downloads

Access the complete technical data, application guidelines, and independent testing for Super Therm®.

Finish It Like the Hoover Dam.

All three Enamo Grip formulas ship anywhere in the United States — spec'd to your exposure by Arin Shahmoradian directly.

Ready to Move Forward?

Four ways to engage with Enamo Grip. Pick the one that fits your project.

Enamo Grip Coverage Calculator

Coverage from the TDS minimum spread-rate tables. Coat count follows your job specification.

Surface area (ft²)
Formula
Finish
Surface condition
Number of finish coats
Rust Grip primer coverage
Enter your surface area and select the product and surface conditions to see the estimated material needed.
Based on supplied product spread rates and includes 10% for waste. Coverage varies by product, finish, surface porosity, and application method. Porous surfaces require Rust Grip primer; non-porous surfaces generally require one finish coat. A second coat is recommended for high-traffic areas. Confirm project requirements with the SPI technical team before ordering.

Frequently Asked Questions About Enamo Grip

Direct answers first — details after. Can't find yours? Call +1 818-696-3786.

Buying & Cost

Where can I buy Enamo Grip?

Enamo Grip®, Enamo Grip II and Enamo Grip 5000 are sold directly by Volta Coatings, the official USA distributor for SPI Coatings, in pre-measured two-part kits, in clear and colors, shipped nationwide. Order through the purchase form on this page.

How much Enamo Grip do I need?

Figure about 200 ft² per gallon per coat for Enamo Grip and Enamo Grip 5000 (8 mils wet / ~4–4.8 mils dry), and 275 ft²/gal for Enamo Grip II (6 mils wet / 3.47 mils dry). Clear Enamo Grip spreads further — roughly 406 ft²/gal high-gloss, 395 semi-gloss, 386 matt. Non-porous surfaces primed with Rust Grip take one coat, with a second coat on floors, handrails and traffic areas; porous surfaces take a priming coat at 150–200 ft²/gal plus one or two finish coats. Add 10% for waste.

Does Enamo Grip ship as hazmat?

Depends on the formula. Enamo Grip II is water-based and not regulated for transport — standard ground freight. Enamo Grip (original) and Enamo Grip 5000 are solvent-based Class 3 flammable liquids (UN 1263) and ship as hazmat ground freight; 1-gallon kit components may qualify for the DOT Limited Quantity exception. Ask for a shipped-total comparison with your zip code and kit count.
Will it work for my situation?

Which Enamo Grip do I need?

Match the formula to the exposure. Enamo Grip (original) — maximum proven exterior durability: ABS marine approval, 5,000-hour ASTM D5894 UV/salt-fog record, the full published test battery. Enamo Grip II — when VOC limits, occupied buildings or water cleanup drive the job: water-based at 22 g/L, same self-leveling film. Enamo Grip 5000 — chemical, fuel and acid-splash service: gasoline, diesel, Skydrol, animal fats, pH 5–14. Not sure? Describe the exposure through the form and we will tell you which kit.

What’s the best topcoat for Rust Grip?

Enamo Grip — it is the topcoat SPI specifies over Rust Grip® and Moist Metal Grip, and the Rust Grip / Enamo Grip combination is tested together to ISO 12944-6 C5-High and 5,000 hours ASTM D5894. It is the system that earned the SSPC E. Crone Knoy Award on the Hoover Dam Bypass Bridge. Rust Grip encapsulates the corrosion; Enamo Grip adds color, gloss, UV stability and a chemical barrier on top. Apply within Rust Grip’s 24-hour window, or lightly sand after.

Can I use Enamo Grip on a garage floor or workshop floor?

Yes — the TDS lists it as a floor covering where a tough, long-lasting finish is required, and it self-levels to a smooth, hard film (3H pencil hardness for the 5000). Prime bare or dusty concrete with Rust Grip, apply one coat of Enamo Grip, then a second coat in the wheel paths and foot-traffic zones. For hot-tire pickup, oil and fuel drips, use Enamo Grip 5000. Allow 10 days (Enamo Grip, EG II) or 15 days (5000) before full service; light foot traffic is fine after a day or two.

Is there a low-VOC two-part polyurethane that meets California air-quality rules?

Yes — Enamo Grip II is an ultra-low-VOC, water-based two-part polyurethane at 22 g/L (0.18 lb/gal), well under the limits of strict air districts such as California’s South Coast AQMD, and suitable for occupied buildings. It mixes 2:1, self-levels like the original, and cleans up with soap and water. Thin with a little potable water (2 oz per gallon) when brushing or rolling.

Is Enamo Grip approved for marine use?

Yes. Enamo Grip and Enamo Grip II are ABS Type Approved (PDA 25-0170157) under IMO FTP Code 2010 Parts 2 and 5 — smoke and toxicity, and low surface flammability — for bulkheads, ceilings and decks, and the TDS lists ABS/IMO marine approvals for saltwater/maritime use, with US Coast Guard and IMO listings under renewal. Enamo Grip 5000 is not covered by the ABS certificate. Enamo Grip over Rust Grip has also completed 5,000 hours of ASTM D5894 cyclic UV/salt fog. Request the current approval documents through the form for a vessel or offshore specification.

Can Enamo Grip go over an existing painted surface or over HPC insulation?

Yes to both, with prep. Over sound existing paint, sand or scuff any gloss to a profile, clean, and apply; over bare or rusting steel, prime with Rust Grip first. Over SPI’s HPC insulation coating on above-grade piping, Enamo Grip is the standard color/weather topcoat, applied in two coats once the HPC is completely dry so the system is water-tight. Enamo Grip is not applied within 2 inches of chlorinated rubber.

How chemical resistant is Enamo Grip 5000?

Enamo Grip 5000 serves across pH 5–14 with excellent alkali resistance, very good acid resistance, and excellent resistance to gasoline, diesel, Skydrol and animal fats — an aliphatic polyester/polyurethane hybrid at 60% solids by volume with 3H pencil hardness. Three field rules from the TDS: rinse acid splash within 72 hours, never apply thick coats, and do not use it for total submersion. Ask for the Enamo Grip 5000 chemical-resistance chart for a specific chemical.

Does Enamo Grip come in clear, and what sheens?

Yes. Enamo Grip (original) comes in clear in three sheens — high-gloss, semi-gloss and matt — and in colors; Enamo Grip II and Enamo Grip 5000 come in clear and colors. Clear is applied in up to three coats on its own (one to three for EG II). All colors are available with established minimum order quantities, so ask about lead time on custom colors.
How to apply

How do you apply Enamo Grip?

Soft-bristle brush, ¼-inch nap roller, or — preferred — airless sprayer at 1.5 gal/min and 3,300 psi with a .011–.015 tip. Mix exactly (3:1 original, 2:1 for II and 5000) for 2 minutes by hand or 30 seconds with a drill blade, no vortex. Apply thin coats and let each tack before the next; thick coats bubble. Apply between 40°F and 100°F ambient, on surfaces up to 150°F, at least 5°F above the dew point, on clean, completely dry, salt-decontaminated surfaces (chlorides 3–5 µg/cm²). Never thin with mineral spirits.

What’s the pot life, and how long do I have to recoat?

Pot life once mixed: 4–6 hours at 70°F for Enamo Grip and Enamo Grip II, 3–4 hours for Enamo Grip 5000 — and about 1 hour at 90°F for all three (as little as 30 minutes above 95°F for EG II, 1.5 hours for the 5000). Set the pails in ice water to extend it. Recoat windows differ: Enamo Grip, 3 hours or less at 70°F; Enamo Grip 5000, 3–4 hours; Enamo Grip II, up to 24 hours while the first coat is tacky with no transfer. After the window, lightly sand before the next coat.

Can I apply Enamo Grip in hot, humid weather?

Yes, with two adjustments. Above 90°F the pot life and recoat window shorten to about 1 hour, so mix smaller batches and keep the pails on ice. In hot (90°F) and humid (85% RH) conditions, SPI’s instructions are to cut a 3-gallon kit with one quart of MAK solvent (methyl n-amyl ketone) for Enamo Grip and Enamo Grip 5000, or one quart of potable water for Enamo Grip II, to slow surface skinning. Stay 5°F above the dew point and keep the surface completely dry.

How long until Enamo Grip fully cures?

Tack-free in 30–60 minutes at 70°F; dry to handle the same day. Full cure is 10 days for Enamo Grip and Enamo Grip II and 15 days for Enamo Grip 5000 (about 80% of properties in the first 72 hours). Once cured, all three withstand continuous service up to 300°F (149°C).

What surface prep does Enamo Grip need?

Clean, dry and free of oil, grease, salts and films. Degrease, pressure wash at about 3,500 psi, and decontaminate salts with Chlor*Rid or equivalent to 3–5 µg/cm² chlorides. Sand any glossy existing coating to a profile. Prime bare steel with Rust Grip and porous surfaces with Rust Grip or a first coat of Enamo Grip. The surface must be completely dry before applying.
Proof & safety

Will Enamo Grip fade or chalk in the sun?

Enamo Grip is an aliphatic polyurethane, and its TDS states “unsurpassed semi-gloss and color retention, as well as chalk resistance, when used in exterior applications.” That holds up in testing — 5,000 hours of ASTM D5894 cyclic UV/salt-fog and 1,500 hours of ASTM G154 UV exposure — and in the field: the Hoover Dam Bypass Bridge handrails have carried Enamo Grip in Nevada desert sun since the bridge opened in 2010 — more than 15 years.

What’s the difference between Enamo Grip and Enamo Grip II?

Chemistry and compliance. Enamo Grip is solvent-based (244 g/L VOC, 3:1 mix, MEK cleanup, hazmat freight) and carries the full published test battery and ABS approval. Enamo Grip II delivers the same self-leveling two-part polyurethane film water-based at 22 g/L (2:1 mix, soap-and-water cleanup, non-hazmat shipping), is also ABS Type Approved, and has a longer 24-hour recoat window. Film hardness and finish quality are the family signature in both.

Is Enamo Grip waterproof?

Yes. Enamo Grip passed ASTM D6904 wind-driven rain testing (DL Labs) with a 0.16 lb weight gain and no dampness on the back of the panel — half the allowable limit — and has water-vapor-transmission data under ASTM E96. It is resistant to water, humidity, stains, acids, solvents and chemicals per the TDS. It is a topcoat, not an immersion lining: do not use any Enamo Grip for total submersion.

Is Enamo Grip fire rated and safe to use indoors?

Enamo Grip has ASTM E84 surface-burning data and, with Enamo Grip II, is ABS Type Approved as a fire-resistive coating under IMO FTP Code Parts 2 and 5 (smoke, toxicity and surface flammability) — the test regime for ship interiors. The liquid solvent-based products are flammable during application: ventilate, keep away from ignition sources and use a respirator. Enamo Grip II is the choice for occupied interiors because it is water-based with minimal odor. Cured Enamo Grip 5000 is non-sparking. Full details are in each SDS.

Need a quantity, a shipped total, or a yes/no on your surface?

Send photos and square footage through the form, or call Volta Coatings at +1 818-696-3786 (Mon–Fri).

Trusted by Industry Leaders Worldwide

Linde
Chevron
Georgia-Pacific
SpaceX
Petrobras
Engie
US Army
HESS
Vela
Halliburton
Covanta Energy
OXY
ADNOC
Berkshire Hathaway Energy
Nakilat
Milaha
Drydocks World
PEMEX
SASOL
Saipem
Volta Coatings

Official USA distributor of SPI Coatings — Rust Grip®, Super Therm®, Enamo Grip®, HPC® Coating. Nationwide shipping.

Made in USA
Made in USA
Products
Contact Us
Certifications
  • Masdar
  • UL
  • FM Approved
  • Cradle to Cradle
  • DNV
  • USDA