Nationwide Shipping
★ ABS Class Certified · US Patent 5,695,812 · Direct to Rust — No Abrasive Blasting

Rust Grip - Marine Coating

Paint Over Rust, Skip the Drydock

Salt never sleeps — and drydock time is the most expensive real estate in your fleet. Rust Grip® is the patented single-component coating that applies directly over rusted steel with no abrasive blasting: pressure wash, decontaminate the salts, and coat — three coats in a single day, pierside or in service. Lab-proven at 15,000 hours of ASTM B117 salt spray with a perfect 10/10 rating, ABS certified, and self-priming — one product from prime to finish, with optional Enamo Grip® and Super Therm® topcoats where color, gloss, or deck heat matter. Used on LNG carriers, workboats, salvage boats, and bulk carriers by the US Army, Nakilat, and Qatar Navigation. Made in USA.

Rusted Deck Plate — Before
Marine Coating - Rusted Deck Plate — Before
Same Deck, Rust Grip Applied — After
Marine Coating - Same Deck, Rust Grip Applied — After
Qatar Navigation Workboat — Three Coats, One Day
Marine Coating - Qatar Navigation Workboat — Three Coats, One Day
Blue Chip Casino Boat — Coated Without Sandblasting
Marine Coating - Blue Chip Casino Boat — Coated Without Sandblasting
Nakilat LNG Carrier — Hard-to-Maintain Areas
Marine Coating - Nakilat LNG Carrier — Hard-to-Maintain Areas
Salvage Rams — Louisiana Wildlife & Fisheries
Marine Coating - Salvage Rams — Louisiana Wildlife & Fisheries
Optional Finish: Rust Grip + Enamo Grip Topcoat
Marine Coating - Optional Finish: Rust Grip + Enamo Grip Topcoat

Rust Grip® — Authorized SPI Distributor  ·  Ships Worldwide with Full DG Documentation

Where's the Rust on Your Vessel?

Decks & Walkways Topsides & Superstructure Deck Machinery, Davits & Cranes Hard-to-Maintain Areas DECKS TOPSIDES MACHINERY STERN GEAR HULL (topside scope)
Tap a zone on the vessel

Every zone runs the same product — Rust Grip®, direct to rust. What changes is the coat spec and the documented proof behind it. Your pick also sets the vessel spec form below.

Rust Grip's marine scope covers decks, topsides, superstructures, machinery, and steel above the waterline. It is not an antifouling or below-waterline immersion system — for underwater hull requirements, ask us about scope during your vessel spec review.

What Does Your Project Need?

Enamo Grip® (Original) selected — specs, calculator, and order form below are set to the original formula.

AS
About Arin Shahmoradian
Official USA distributor of Rust Grip® (SPI Coatings). Volta Coatings has shipped Rust Grip to industrial, marine, farm, and residential customers across the United States and internationally for over a decade. Direct technical support before, during, and after every project. Reach him directly at +18186963786 or arin@voltacoatings.com

Why Do Marine Coatings Fail — and Why Does Rust Grip Hold?

Marine coatings fail for two reasons: salt that was never removed from the steel, and downtime economics that force shortcuts. Conventional systems demand abrasive blasting to near-white metal — which means drydock, containment, and lost charter days — so corroded steel waits, and rust wins. Rust Grip® inverts the economics: it penetrates and encapsulates the rust itself, curing by absorbing moisture from the air — the humidity that kills other coatings accelerates this one. Pressure wash, decontaminate chlorides, and apply three coats in a single day, pierside. The 15,000-hour salt-spray record says the shortcut isn't a compromise; the Blue Chip Casino Boat's $2,000,000 saving says it's a strategy.

Verified Marine Results

Every card below is documented — the letters are further down this page.

Marine Coating - Blue Chip Casino Boat — Boyd Gaming

Blue Chip Casino Boat — Boyd Gaming

📍 Michigan City, USA

Saved $2,000,000 by coating with Rust Grip instead of sandblasting.

✓ VERIFIED
Marine Coating - Qatar Navigation Workboats

Qatar Navigation Workboats

📍 Doha, Qatar

Three coats in a single day to save time and money — per the captain's letter.

✓ VERIFIED
Marine Coating - Qatar Navigation — 2-Year Update

Qatar Navigation — 2-Year Update

📍 Doha, Qatar

Re-documented two years after the one-day application — protection holding.

✓ VERIFIED
Marine Coating - Nakilat LNG Carriers

Nakilat LNG Carriers

📍 Qatar — Al Mafyar

"Excellent performance on hard to maintain areas" across several years on an LNG carrier.

✓ VERIFIED
Marine Coating - Mubarak Challenger — ABS Class

Mubarak Challenger — ABS Class

📍 Dubai, UAE

Deck coated after Offshore Arabia 2010; one year on, "still no signs of corrosion development."

✓ VERIFIED
Marine Coating - Louisiana Wildlife & Fisheries

Louisiana Wildlife & Fisheries

📍 Louisiana, USA

Rusted, pitted salvage rams stripped, Rust Gripped, topcoated — "one less thing we have to worry about."

✓ VERIFIED

Laboratory and field project results may vary according to climate conditions.

How Proven Is Rust Grip at Sea? The Test Record

Salt Spray — ASTM B117

15,000 Hrs — 10/10

Rust Grip at just 6 mils DFT held a perfect 10/10 through 15,000 hours of continuous salt spray — the longest-running number on this site.

Cyclic Salt Fog — ASTM D5894

10,000 Hrs — 10/10

UV + salt fog cycling rated per ASTM D610-08 — full ratings table in the lab record below.

ISO 12944-9 — Petrobras

Best of 3 Tested

"Among the 3 tested zinc-free single component paint systems, the RUST GRIP showed the best performance."

Class Certified

ABS

Rust Grip carries an ABS certificate — displayed on this page and available for your submittal.

Documented Savings

$2,000,000

One vessel, one decision: Blue Chip Casino Boat coated direct-to-rust instead of sandblasting.

Patented Chemistry

US 5,695,812

Single-component, moisture-cure polyurethane loaded with metallic pigments — humidity accelerates the cure.

The Lab Record, In Full

Marine buyers read the actual numbers — so here they are, at just 6 mils dry film thickness.

ASTM B117 — 15,000 Hours

Continuous salt spray for 15,000 hours with a

perfect 10/10 rating

— no blistering, no rusting, no failure at the scribe. Most marine specifications ask for 1,000–5,000 hours; Rust Grip's report runs three to fifteen times longer.

ASTM D5894 — 10,000 Hours

Cyclic UV + salt fog, rated per ASTM D610-08 across three coupons:

Hours Coupon 1 Coupon 2 Coupon 3
1,000 10 10 10
5,000 9-P 10 10
10,000 9-P 10 10

9-P reflects pinpoint blistering at the coupon edge — an edge effect of the test panel, not a coating deficiency.

ISO 12944-9 — Petrobras

Offshore-grade cyclic aging:

"Among the 3 tested zinc-free single component paint systems, the RUST GRIP showed the best performance."

Pull-off adhesion measured 1,813 psi (12.5 MPa) initial and 1,638 psi (11.3 MPa) after 12 full cycles.

Full reports are available in the downloads section below; the ABS certificate is displayed further down this page.

Rust Grip in the Field

Click thumbnails to view full size.

Marine Coating - Project Image 1Marine Coating - Project Image 2Marine Coating - Project Image 3Marine Coating - Project Image 4Marine Coating - Project Image 5Marine Coating - Project Image 6Marine Coating - Project Image 7Marine Coating - Project Image 8Marine Coating - Project Image 9Marine Coating - Project Image 10Marine Coating - Project Image 11Marine Coating - Project Image 12

Application at Sea: The Rules

Field guidance from Arin Shahmoradian, USA Distributor — based on SPI application instructions

RULE #1 — MOST IMPORTANT
Kill the salts before you coat anything.
Chlorides are the reason marine coatings fail young. Pressure wash, then decontaminate with Chlor*Rid or equivalent to acceptable levels — chlorides 3–5, nitrates 5–10, sulfates 5–10 mcg/cm² — and let the surface dry. On a vessel this step is the job; the coating is the reward.
Humidity is your friend — watch the overcoat clock.
Rust Grip cures by absorbing moisture from the air, so marine humidity accelerates it: at 80–90% RH and 70–90°F the overcoat window is roughly 1–1.5 hours (full table below). That's how Qatar Navigation put three coats on in a single day — plan crews and batches around the table.
RH 90°F 70°F 50°F
90% 1 hr 1.5 hr 2-3 hr
80% 1 hr 1.5 hr 2-3 hr
60% 1.5 hr 1.5-2 hr 3–4 hr
40% 1–2 hr 2–4 hr 6–8 hr
30% 2–3 hr 3–6 hr 10–14 hr
20% 6 hr 8–10 hr 12–16 hr
10% 12 hr 12–18 hr 18–24 hr
Match the coat count to the corrosion.
Light-to-medium rust: 2 coats (~90 ft²/gal incl. waste). Heavy rust, industrial and marine service: 3 coats (65 ft²/gal theoretical / 58.5 ft²/gal with waste). Rust Grip is self-priming — no topcoat is required for protection. Where color, gloss, or deck heat matter, add a topcoat inside Rust Grip's overcoat window (see Optional Topcoats below).
SURFACE PREP
Remove loose/pack rust mechanically; no abrasive blasting required in most cases; salts to spec; completely dry.
RUST GRIP DATA
Single component · solids 62.2% wt / 51.4% vol · 9.4 lbs/gal · VOC 380 g/L · apply 50–200°F · 325°F max cured.
OVERCOAT WINDOW
RH-driven — 1 hr at 90% RH/90°F up to 12–24 hrs at 10% RH/50°F. Recoat inside the window.
APPLICATION
Brush, roller, or airless. Single component — no mix ratios, no pot life on a moving deck.
SHIPPING & DG
Ships UN1263 Class 3 with full IMO/IATA documentation and forwarder briefing handled by Volta.

Why Rust Grip Outperforms at Sea

No Blasting, No Drydock
Direct-to-rust application pierside or in service — the $2,000,000 Blue Chip math, available to every hull in the fleet.
Single Component
No mix ratios, no pot life, no wasted kits on a moving deck — open the pail and coat. Crews get it right the first time.
Humidity Works for You
Moisture-cure chemistry turns marine air into a cure accelerator — three coats in a single working day.
The Longest Salt Record on the Page
15,000 hours B117 at a perfect 10/10 and 10,000 hours cyclic salt fog — at just 6 mils DFT.
Self-Priming, Surface Tolerant
Primer, mid, and finish in one product over sound rust, pitted steel, and complex geometry — davits, rams, and stern gear included.
Class-Ready Paperwork
ABS certificate on file, DNV/UL/FM badges — and Volta handles the DG shipping documentation to any yard, US or international.

Rust Grip Certifications

ABS
Certificate on file — displayed below.
DNV
Badge on file.
UL
Listed.
FM
Approved.
C2C / MASDAR
Badge on file.
US PATENT
5,695,812 — direct-to-rust chemistry.
★ Industry Recognition

ABS Certification on File

Rust Grip's ABS certificate is displayed here in full — and the current certificate and class documentation are available for your submittal package. Request them through the vessel spec form below.

Marine Coating - Hoover Dam Bypass Bridge

Purchase Rust Grip. Ships Worldwide.

Tell us the vessel, the zones, and the condition of the steel; Arin Shahmoradian will spec coat counts, quantities, optional topcoats, and DG shipping to your yard — US or international. Monday–Saturday. Authorized SPI Distributor — Volta Coatings.

  • By submitting, you agree to our Terms of Service and Privacy Policy

    Both checkboxes optional — the form submits either way.

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.

Topcoats Over Rust Grip: Enamo Grip® & Super Therm®

Rust Grip is self-priming and needs no topcoat for protection.
Two SPI topcoats earn their place when the vessel asks for more — applied inside Rust Grip's overcoat window.

Enamo Grip®

Color, Gloss & Wear

The two-part aliphatic polyurethane finish coat — ABS approved for saltwater/maritime use, self-leveling, with hard scuff and impact resistance for decks and traffic zones. It's the third coat in Qatar Navigation's own spec: two coats Rust Grip, one coat Enamo Grip, rated "very good" at the one-year mark. Clear and colors. Enamo Grip® →
Super Therm®

Deck Heat & Solar Load

The NASA-developed ceramic coating for sun-hammered decks and topsides — documented IR readings on a Vela International vessel measured 107.6°F on Super Therm vs 112.3°F on standard white and 133.5°F on red paint, with cabin-side surfaces at 82.9°F. Water-based and ABS fire-resistive rated. Super Therm® →

Rust Grip Marine Specifications

Chemistry Single-component moisture-cure polyurethane, metallic pigments · US Patent 5,695,812
Solids 62.2% by weight / 51.4% by volume
Weight / VOC 9.4 lbs per gallon · 380 g/L
Cure Absorbs moisture from the air — humidity accelerates; overcoat per RH table above
Surface temp 50–200°F applying · 325°F max after cure
Adhesion (ISO 12944-9) 1,813 psi initial · 1,638 psi after 12 cycles
Shelf life 3 years unopened
Full data Rust Grip® product page →
Heavy rust — industrial & marine (3 coats) ≈ 61.2 ft²/gallon including 10% waste and spillage
Light-to-medium rust (2 coats) ≈ 90 ft²/gallon including 10% waste and spillage
Optional Enamo Grip® finish coat ≈ 200 ft²/gallon per coat, applied inside Rust Grip's overcoat window
Optional Super Therm® deck coat ≈ 91 ft²/gallon (1 coat at 10 mils DFT incl. waste)

Surface prep: remove loose and pack rust mechanically (wire brush, power tool, needle gun); no abrasive blasting required in most cases. Clean of oil, tar, grease, salts, and films — TSP or citrus cleaner plus pressure wash; decontaminate salts with Chlor*Rid or equivalent to chlorides 3–5, nitrates 5–10, sulfates 5–10 mcg/cm²; surface completely dry. Apply by brush, roller, or airless sprayer between 50–200°F surface temperature. Single component — no mixing. Recoat inside the RH-driven overcoat window (table above). Topcoats, where specified, apply inside the same window.

Stop Paying for Rust Twice.

Direct-to-rust, pierside, class-documented — spec'd to your vessel by Arin Shahmoradian.

Ready to Move Forward? Four Ways to Start

Letters of Recommendation

Mubarak Marine - Metal Work Boats - Dubai, UAE - Technical Department

ABS Class Vessel Mubarak Challenger - deck application, 1+ year service

"After meeting your company at the Off Shore Arabia Conference in April 2010, we decided to use Rust Grip on the deck of our ABS Class vessel Mubarak Challenger. It has now been over a year, and there are still no signs of corrosion development as originally promised by your company."

Qatar Navigation - Doha, Qatar - Capt. Frazier Pinto

Marine workboat - Rust Grip + Enamo Grip topcoat system, 1 year service

"It's been a year since the application of special coating of 1st & 2nd Coat (Spray) Rust Grip & 3rd Coat (Spray) Enamo Grip. The overall results of protection against environmental corrosion by the coatings is very good."

Nakilat - LNG Carriers - Qatar - Capt. Marin Telak

Al Mafyar LNG Carrier - hard-to-maintain areas, multi-year service

"I was using it on Al Mafyar LNG Carrier for last few years and it shows excellent performance on hard to maintain areas."

Louisiana Wildlife and Fisheries - Jeff Canulette

State agency equipment maintenance - hydraulic rams, 2019 application

"I try to Rust Grip every piece of steel I can, because it really helps us save time and money on maintenance. Once I Rust Grip something I do not have to worry about it again. We love your product and we are always trying to make our job easier, and this is one less thing we have to worry about once it is on. The pictures with the rusted, pitted rams are from 2019, where we took them off the aframe, removed the rust, applied the Rust Grip and painted them with a one part polyurethane paint."

Marine Spread Rate Calculator

Coverage from the TDS minimum spread-rate tables. Coat count follows your job specification.

Surface area (ft²)
Rust Grip Spec

Add Enamo Grip® finish coat (+1 coat @ 200 ft²/gal)

Enter your surface area to see gallons needed.
Estimates only — coat count and thickness follow the job specification. Call +1 818-696-3786 to confirm.

Frequently Asked Questions

Direct answers first — details after. Can't find yours? Call +1 818-696-3786.

Buying & Cost

Where can I buy Rust Grip marine coating?

Directly from Volta Coatings, the official USA distributor for SPI Coatings. Rust Grip® ships nationwide to yards and docks, and worldwide with full dangerous-goods documentation handled for you. Order through the form on this page.

How much Rust Grip does my boat or barge need?

Three coats for marine steel at 65 ft² per gallon theoretical — 58.5 ft²/gal with the 10% waste allowance the calculator on this page uses. Light-to-medium rust on topsides takes two coats at 100 ft²/gal (90 with waste). An optional Enamo Grip® finish coat adds about 200 ft²/gal. Measure deck, bulwark, superstructure and hull-above-waterline areas separately, run the calculator, then send the vessel details through the form for a confirmed quantity. Pitted deck plate uses more on the first coat.

Can you ship Rust Grip internationally to our yard?

Yes. Rust Grip ships as UN 1263 Class 3 dangerous goods (Packing Group III) by ground, sea (IMDG) or air (IATA), and Volta Coatings prepares the documentation and briefs the forwarder for US and international shipyard deliveries. Send the destination port and quantity for lead times.

Why is Rust Grip cheaper than blasting and repainting a workboat?

Because it removes the biggest line item — abrasive blasting and the downtime around it. Rust Grip is applied over firmly bonded rust after power-tool cleaning, pressure washing and salt removal; SPI’s TDS states a white or near-white blast is not required in most cases. The Blue Chip Casino Boat saved $2,000,000 against the sandblasting alternative. For a workboat or barge, that usually means the vessel is coated pierside between jobs instead of hauled out.
Will it work for my vessel?

Can you paint directly over rust on a ship or barge?

Yes — that is what Rust Grip® was patented for (US Patent 5,695,812). It is a single-component, moisture-cure polyurethane that penetrates and encapsulates sound, firmly bonded rust. The sequence: remove loose and pack rust mechanically (SSPC-SP 2/SP 3), pressure wash, decontaminate salts, let it dry completely, coat. No abrasive blasting is required in most cases.

Is Rust Grip ABS approved?

Yes. Rust Grip® holds ABS Type Approval (PDA 25-0189406, valid through 2029/2030) as a fire-resistive coating under IMO FTP Code 2010 Parts 2 and 5 — smoke and toxicity, and low surface flammability — for bulkheads, ceilings and decks, and is listed under EU MED 2014/90/EU. The certificate is displayed on this page and available for your submittal package. It also carries DNV, UL and FM badges. Its specified marine topcoat, Enamo Grip®, holds its own ABS approval.

Is Rust Grip right for steel workboats, tugs and deck barges?

Yes — it is the typical fit. Workboats and barges rust at the deck plate, bulwarks, hatch coamings, winch foundations, push knees and anywhere cargo and lines chew through paint, and they rarely sit idle long enough for a full blast-and-repaint. Rust Grip goes on over prepared rust between jobs, cures by humidity (an advantage on the water), resists impact and abrasion (ASTM D2794, D4060), and is UV-stable so decks do not need a topcoat unless you want color or non-skid. It is also tested to ISO 12944-9 offshore and ISO 12944-6 C5-High, the categories for splash-zone and coastal steel.

Does Rust Grip need a topcoat on a vessel?

No — Rust Grip is self-priming and fully protective on its own, curing to a metallic silver finish that does not chalk. Topcoats are optional: Enamo Grip® for color, gloss and wear on decks, walkways and handrails, or Super Therm® where deck heat is the complaint. Apply either within Rust Grip’s 24-hour window, or lightly sand after.

Does Rust Grip work below the waterline?

No — and we would rather tell you here than in a claim dispute. Rust Grip’s marine scope is decks, topsides, superstructure, machinery, and steel above the waterline and in the splash zone. It is not an antifouling or immersion-service hull system. If your project includes underwater hull work or ballast tanks, raise it in the vessel spec review and we will define the scope line and the right SPI product.

Can Super Therm keep a steel deck and the cabins under it cool?

Yes — and the measurement that matters is under the deck plate, not on top of it. On the Vela International VLCC Alphard Star in July 2012 (outside air 34°C / 93°F), the ship’s officers read the top of the Super Therm-coated deck at 42.0°C and the standard white paint beside it at 44.6°C — only 2.6°C apart. Under the same two deck plates, measured from the cabins below, the steel under white paint was 40.3°C (105°F) and the steel under Super Therm was 28.3°C (83°F): a 12°C (22°F) difference. That is the difference between a coating that reflects at the surface and one that stops heat loading into the steel, and the crew reported a noticeable temperature difference in the cabins under the coated decks. The gap varies month to month with sun angle and air temperature. Other readings: Milaha LNG-carrier deck covers 98°F coated vs 142°F standard paint; Zamil Steel (Dammam) panel underside 26°C vs 31.9°C after three hours of sun. Readings are site-specific and vary with weather, orientation and application.

Will Rust Grip hold up against diesel, hydraulic oil and deck chemicals?

Yes for splash and spill. Rust Grip resists most solvents, chemicals and acid splash and has passed 24-hour exposure to 12 reagents. Where decks see constant fuel, hydraulic fluid or chemical contact, finish with Enamo Grip 5000, which is rated for gasoline, diesel, Skydrol and pH 5–14 service. Neither is an immersion lining for tanks.
How to apply

How is Rust Grip applied on a working vessel?

Brush, roller, or airless sprayer with a .015 tip — and because it is single-component there are no mix ratios, no pot life and no wasted kits on a moving deck. Prep is mechanical rust removal, pressure wash and salt decontamination; then coat, and recoat any time after the thumb test (press firmly — thumb comes away clean, no fingerprint) and within 24 hours. Several coats in one shift are normal in marine humidity.

Can Rust Grip be applied in humid, salty air?

Humidity is this chemistry’s advantage: Rust Grip cures by absorbing moisture from the air, so warm, humid marine conditions make it tack-free faster (30–60 minutes at 70°F), not slower. A 5 mph breeze is enough to keep the steel surface dry; stay 5°F above the dew point and never coat damp steel. The one non-negotiable is salt decontamination before coating: chlorides to 3–5 µg/cm² with Chlor*Rid or equivalent. Where salts cannot be brought that low, Rust Grip permits 10–50 µg/cm² with two additional dry mils.

Do I have to drydock the vessel to coat it?

For Rust Grip’s scope — decks, topsides, superstructure, machinery and steel above the waterline — no. It applies pierside or in service, and marine humidity speeds the cure: Qatar Navigation applied three coats in a single working day. Below-waterline work follows your class and docking schedule as usual.

What surface prep does a rusted deck need?

Remove loose scale and pack rust with needle-free power tools or a zip gun (SSPC-SP 3), pressure wash at about 3,500 psi with Chlor*Rid to pull chlorides out of the pits, test salts, and let the steel dry completely — wipe with acetone if in doubt. Firmly bonded rust stays; it is the profile Rust Grip grips. Do not use needle guns, muriatic acid washes or mineral spirits under Rust Grip, and remove any inorganic zinc primer above 8.2 kg zinc/gal before coating.

How many coats on a barge deck, and how thick?

Three coats at 8 mils wet / 4 mils dry each on pitted or heavily rusted marine steel, two coats on lightly rusted topsides. The requirement is 4 mils dry over the highest peak of the profile — the first coat fills the pits, so measure DFT after the second coat and add a third where the peaks are not covered. Stripe-coat welds, edges and coamings first.
Proof & safety

How long does Rust Grip hold up in salt-water conditions?

The lab record: 15,000 hours of ASTM B117 salt spray with a perfect score at one coat of 6 mils, 10,000 hours of ASTM D5894 cyclic UV/salt fog at a perfect 10, ISO 12944-6 C5-High and ISO 12944-9 offshore qualification. The field record: Nakilat reports excellent performance across several years on an LNG carrier; the Mubarak Challenger’s deck showed no corrosion development at its one-year mark; and on the Vela VLCC Alphard Star, Rust Grip applied over rusted steel without blasting was inspected by the ship’s officers in July 2012 — in the acid-soot zone beside the funnel — with no rust spots, bubbling or pitting anywhere on the coated surface.

What topcoats work over Rust Grip on a vessel?

Two are specified: Enamo Grip®, the ABS Type Approved two-part polyurethane finish (the third coat in Qatar Navigation’s own spec) for color, gloss and deck wear; and Super Therm®, the ceramic coating developed with NASA’s Marshall Space Flight Center materials lab, for deck and superstructure heat. Rust Grip accepts both solvent- and water-based topcoats; for another manufacturer’s topcoat, run an ASTM D4541 pull-off on a test patch.

Is Rust Grip fire-safe for crew spaces and engine rooms?

Yes — its ABS Type Approval is specifically as a “Coating, Fire Resistive” under IMO FTP Code 2010 Parts 2 and 5 for bulkheads, ceilings and decks, meaning it meets the smoke, toxicity and low-flame-spread limits for ship interiors. It also carries ASTM E84 surface-burning data and a Class A rating under ASTM E108. The liquid is flammable during application: ventilate confined spaces and keep ignition sources clear; the cured film is non-sparking.

What about aluminum crew boats and non-skid decks?

Rust Grip is a steel system. On aluminum there is no rust profile to grip, so the surface is sweep-blasted or primed with SPI’s SP Etch Primer before an Enamo Grip finish — tell us the alloy and we will specify it. For non-skid on steel decks, Rust Grip is the base and an Enamo Grip coat with broadcast aggregate is the usual finish; ask for the application sequence.

Need a quantity, a shipped total, or a yes/no on your surface?

Send photos and square footage through the form, or call Volta Coatings at +1 818-696-3786 (Mon–Fri).

Trusted by Industry Leaders Worldwide

Linde
Chevron
Georgia-Pacific
SpaceX
Petrobras
Engie
US Army
HESS
Vela
Halliburton
Covanta Energy
OXY
ADNOC
Berkshire Hathaway Energy
Nakilat
Milaha
Drydocks World
PEMEX
SASOL
Saipem
Volta Coatings

Official USA distributor of SPI Coatings — Rust Grip®, Super Therm®, Enamo Grip®, HPC® Coating. Nationwide shipping.

Made in USA
Made in USA
Products
Contact Us
Certifications
  • Masdar
  • UL
  • FM Approved
  • Cradle to Cradle
  • DNV
  • USDA